Lighting Your Remington Propane Tank Top Heater: A Guide

Remington propane heaters are a great way to keep warm, especially in outdoor settings. They are reliable, tough, and versatile, making them perfect for various activities like camping, tailgating, and ice fishing. Remington offers a range of propane heaters with different BTU outputs, so you can choose the one that best suits your needs. Before lighting your Remington propane tank top heater, always ensure you are in a well-ventilated area and follow the necessary safety precautions.

Set up outdoors on a non-combustible surface

Setting up your Remington propane tank top heater outdoors is simple, but it's important to place it on a non-combustible surface, like asphalt or concrete. This is crucial for safety reasons, as propane heaters can be dangerous if used incorrectly.

To begin, find a suitable outdoor area and place your heater on the ground. Make sure the surface is non-combustible and that there is plenty of ventilation. Keep the heater away from any combustible materials, such as paper or wood, as these could catch fire if they come into contact with the heater's flame or heat.

Once you have found a safe location, follow these steps:

• Check the regulator for any damage or wear and tear. The regulator is a circular device with a rubber cap, usually found at the bottom of the heater. If it is damaged or worn, replace it with a new one before proceeding.
• Remove the valve cap from the top of your propane tank.
• Attach the heater to the tank by inserting the heater's regulator into the valve and securing it by twisting the rubber fastener.
• Open the valve by turning the handle counterclockwise until it stops.
• Turn the regulator knob on the front of the regulator to the medium setting by twisting it anti-clockwise.
• Use a long match or a lighter to ignite the heater. Hold the flame about 1 inch (2.5 cm) away from the mesh screen on the regulator.
• Press and hold the button on the safety shut-off valve, located at the end of the stem holding the mesh screen. Keep holding it until the burner lights, and for an additional 30 seconds after ignition.

Remember always to exercise caution when using a propane heater. Ensure there is adequate ventilation, and never leave the heater unattended or allow children to play nearby. Keep flammable materials away from the heater at all times.

Check the regulator for damage

Before lighting a propane heater, it is important to check the regulator for damage or wear and tear. The regulator is a circular device with a rubber cap, usually found at the bottom of the heater, and it controls the flow of gas in the propane heater while lowering the pressure in the tank. A damaged regulator can lead to gas leaks, fires, and explosions, so it is crucial to inspect it regularly.

• Gas Leak: Check for leaks by applying soapy water to the connections and looking for bubbles. A propane leak will also have a distinct odour similar to rotten eggs or skunk spray.
• Low Flame or Heat Output: Difficulty in lighting the heater or a decrease in heat output may be caused by a reduced gas flow due to a malfunctioning regulator.
• Yellow or Orange Flame: A properly functioning propane appliance should produce a blue flame. A yellow or orange flame could indicate a combustion issue caused by a faulty regulator.
• Unexpected Shutdowns: A properly functioning appliance should not shut down suddenly. Inconsistent gas flow, which could be caused by a faulty regulator, may lead to unexpected shutdowns.
• Frost or Ice on the Regulator: The formation of frost or ice on the regulator suggests an excessive drop in pressure, leading to temperature drops and subsequent condensation.
• Unusual Whistling Sound: While some operational noise is normal, be concerned if you hear unusually loud hissing or persistent whistling near the regulator, as this could indicate a faulty regulator.
• Excessive Gas Consumption: If your appliance is using more propane than usual without any change in usage patterns, it could mean the regulator is faulty and is wasting gas.
• Visible Damage: Check for visible signs of damage, such as cracks, dents, loose connections, or corrosion, as these could impact the regulator's performance.
• Low Reading on Pressure Gauge: If the pressure gauge reads lower than expected, try disconnecting and reconnecting the tank. If this doesn't solve the issue, the regulator may need to be replaced.

If you notice any of these signs, it is important to address the issue promptly. A damaged or faulty regulator can compromise the safety and efficiency of your propane heater.

Attach the heater to the tank

To attach the heater to the tank, start by locating the valve cap at the top of the propane tank. Pull the cap off the valve. Now, hold the heater upright and insert the heater's regulator into the valve. Secure the connection by twisting the rubber fastener. If you have difficulty removing the valve cap, consider putting on a glove to allow you to use more force without damaging your hand.

Open the valve and turn the regulator knob

To light a Remington propane tank top heater, you must first open the valve and turn the regulator knob to the medium setting. This is a crucial step in the process of lighting your propane heater. Here is a detailed, step-by-step guide to help you understand and perform this step effectively:

• Locate the Valve Cap and Regulator: The valve cap is usually found at the top of your propane tank. The regulator is a circular device with a rubber cap, typically located at the bottom of the heater.
• Open the Valve: To open the valve, turn the handle located on top of the valve cap. Keep turning it in a counter-clockwise direction until it reaches its maximum opening point.
• Adjust the Regulator Knob: Find the knob on the front of the regulator. Turn this knob anti-clockwise until it reaches the "medium" setting. This setting is crucial for ensuring you don't overexert the heater or release too much propane at once.
• Understand the Regulator's Function: The regulator plays a vital role in managing the gas pressure and controlling the flow of propane from the tank to the heater. It ensures a consistent and safe release of propane, making it a critical safety feature.
• Check for Damage: Before proceeding, it is essential to inspect the regulator for any signs of damage, wear, or tear. If the regulator is cracked, damaged, or worn out, do not proceed, and replace it with a new one to ensure safety.
• Be Mindful of Safety: Working with propane can be dangerous, so always exercise caution. Ensure you are in a well-ventilated area, preferably outdoors, when opening the valve and turning the regulator knob. Keep children and pets away from the heater during this process.
• Follow the Manufacturer's Instructions: Refer to the user manual or instructions provided by the manufacturer of your Remington propane tank top heater. They may have specific guidelines or variations in the steps for opening the valve and turning the regulator knob for your particular model.

Remember, opening the valve and turning the regulator knob is a critical step in lighting your Remington propane tank top heater. Always exercise caution, follow safety procedures, and refer to the manufacturer's instructions for the best results.

Light with a match or lighter

To light a Remington propane tank top heater with a match or lighter, follow these steps:

Firstly, ensure your heater is set up outdoors on a non-combustible surface, like asphalt or concrete. Propane heaters are dangerous when lit indoors due to the lack of oxygen available to dilute the carbon monoxide they produce.

Next, check the regulator for any damage or wear and tear. The regulator is a circular device with a rubber cap, usually found at the bottom of the heater. If it is damaged, it will need to be replaced before proceeding.

Now, remove the valve cap from the top of your propane tank and attach the heater securely by inserting the heater's regulator into the valve and twisting the rubber fastener.

Once the heater is attached, open the valve by turning the handle on the valve cap. Then, locate the knob on the front of the regulator and twist it anti-clockwise to the medium setting.

Now you're ready to light your heater. Hold a match or lighter about 1 inch (2.5 cm) away from the mesh screen on the regulator. If there is metal wiring in front of the mesh screen, you may need to use extra-long matches or a lighter.

Finally, push and hold the button on the safety shut-off valve, which is located at the end of the stem holding the mesh screen. Keep holding the button for 30 seconds after the burner ignites, then slowly release it.

Your Remington propane tank top heater should now be lit and providing warmth. Remember to always follow safety procedures when using propane heaters and ensure adequate ventilation in the area you are using it.

Frequently asked questions